code updates

main.py

@@ -1,7 +1,10 @@
 import spidev
 from util import *
 from receive import receive_packet
+
 debug = True
+GDO0_PIN=23, 
+GDO2_PIN=24
 
 def menu():
     print("\nMenu")
@@ -12,35 +15,44 @@ def menu():
     print("5: Run Read+Write test")
     print("0: Quit")
 
+
 if __name__ == "__main__":
+
+    init_gpio(GDO0_PIN, GDO2_PIN)
+
     spi = spidev.SpiDev()
     spi.open(0, 0)  # Bus 0, CE0 (Pin 24)
-    spi.max_speed_hz = 8000000  # Safe start speed
+    # spi.max_speed_hz = 8_000_000  # Safe start speed
+    spi.max_speed_hz = 100_000  # Safe start speed
+
     spi.mode = 0b00  # SPI mode 0
     stop = False
 
-    print("Sending SRES (reset)...")
+    print_gdo_state(GDO0_PIN, GDO2_PIN)
+
+    # print("Sending SRES (reset)...")
     spi.xfer2([SRES])
     sleep(0.5)
 
-    print("Sending SNOP (no-op)...")
+    # print("Sending SNOP (no-op)...")
     status = spi.xfer2([SNOP])[0]
     print(f"Status byte: 0x{status:02X}")
 
+    # print("Reading MARCSTATE...")
+    marc = spi.xfer2([MARCSTATE| 0x80, 0x00])[0]
+    print(f"Marcstate byte: 0x{marc:02X}")
+
     print("Reading VERSION register...")
     version = read_register(spi, VERSION)
-    print(f"CC2500 VERSION register: 0x{version:02X}")  
-
-    test_read_write_reg(spi)
-
-    init_regs(spi)
-    sleep(0.1)
-
-
+    print(f"CC2500 VERSION register: 0x{version:02X}")
 
     reg_name = ""
     reg_hex_val = ""
     try:
+        # if version != 0x0F:
+        #     raise Exception("Expected Version was 0x0F!! Quitting")
+        test_read_write_reg(spi)
+        init_regs(spi)
         while not stop:
             menu()
             cmd = int(input("$: "))
@@ -60,7 +72,7 @@ if __name__ == "__main__":
                 value_check = read_register(spi,addr)
                 print("Updated Value: " + hex(value) +" == " + str(value))
             elif cmd == 3:
-                dump_regs(spi)
+                dump_regs(spi, True)
             elif cmd == 4:
                 receive_packet(spi)
             elif cmd == 5:
@@ -70,4 +82,6 @@ if __name__ == "__main__":
                 print("Invalid command")
     finally:
         print("Closing SPI...")
+        sleep(0.1)
         spi.close()
+        sleep(0.1)

transmit.py

@@ -1,17 +1,22 @@
-def burst_write(addr, data):
+from util import strobe, get_addr
+
+def burst_write(spi, addr, data):
     """Write multiple bytes to FIFO or registers"""
-    BURST = 0x40
+    BURST = get_addr("BURST")
     spi.xfer2([addr | BURST] + data)
 
 
 def send_packet(data):
     # Flush TX FIFO
-    strobe(0x3B)  # SFTX
+    SFTX = get_addr("SFTX")
+    strobe(SFTX)  
 
     # Load data to TX FIFO (fixed length)
-    burst_write(0x3F, data)  # 0x3F = TX FIFO
+    TXFIFO = get_addr("TXFIFO")
+    burst_write(TXFIFO, data)  # 0x3F = TX FIFO
 
     # Strobe STX to transmit
-    strobe(0x35)  # STX
+    STX = get_addr("STX")
+    strobe(STX)  # STX
 
     print(f"Sent: {data}")

util.py

@@ -1,5 +1,6 @@
 from init_regs_value import init_regs_value
 from regs_addr import regs_addr
+import RPi.GPIO as GPIO
 import time
 CONFIG_REGS = regs_addr["CONFIG_REGS"]
 STROBES = regs_addr["STROBES"]
@@ -10,6 +11,33 @@ ACCESS = regs_addr["ACCESS"]
 SRES = STROBES["SRES"]
 SNOP = STROBES["SNOP"]
 VERSION = STATUS["VERSION"]
+MARCSTATE = STATUS["MARCSTATE"]
+
+def init_gpio(GDO0_PIN=23, GDO2_PIN=24):
+    # Use BCM numbering
+    GPIO.setmode(GPIO.BCM)
+
+    # Set up GPIO 23 and 24 as inputs
+    # GPIO.setup(GDO0_PIN, GPIO.IN)
+    # GPIO.setup(GDO2_PIN, GPIO.IN)
+    GPIO.setup(GDO0_PIN, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
+    GPIO.setup(GDO2_PIN, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
+
+
+# def clear_csn():
+#     CSN_PIN = 8  # CE0 = GPIO8 (Pin 24)
+#     GPIO.setmode(GPIO.BCM)
+#     GPIO.setup(CSN_PIN, GPIO.OUT)
+#     sleep(0.1)
+#     GPIO.output(CSN_PIN, GPIO.HIGH)
+#     sleep(0.1)
+
+def print_gdo_state(GDO0_PIN=23, GDO2_PIN=24):
+    gdo0 = GPIO.input(23)  # Reads 1 or 0
+    gdo2 = GPIO.input(24)
+    print(f"GDO0 (GPIO23): {gdo0}, GDO2 (GPIO24): {gdo2}")
+    sleep(0.1) 
+
 
 def get_addr(name):
     addr = ""
@@ -26,15 +54,18 @@ def get_addr(name):
 def strobe(spi, command):
     """Send a command strobe to CC2500"""
     spi.xfer2([command])
+    sleep(0.1)
 
 def write_reg(spi, addr, value):
     """Write single byte to a register"""
     spi.xfer2([addr, value])
+    sleep(0.1)
 
 def read_register(spi, addr):
     READ_SINGLE = get_addr("READ_SINGLE")
     # Send address | 0x80 (read), then 0x00 dummy to clock in response
     response = spi.xfer2([READ_SINGLE | addr, 0x00])
+    sleep(0.1)
     return response[1]
 
 def disable_crc(spi):
@@ -52,20 +83,26 @@ def test_read_write_reg(spi, dbg=False):
     write_reg(spi, FIFOTHR, test_value)
     check = read_register(spi, FIFOTHR)
     write_reg(spi, FIFOTHR, initial_val)
-    if(dbg):
+    if(check != test_value):
         print("initial value ", initial_val)
         print("test value ", test_value)
         print("check ",check)
-    elif (not dbg and (check != test_value)):
-        raise Exception("Test Read+Write failed")
+        if(not dbg):
+            raise Exception("Test Read+Write failed")        
     return check == test_value
 
-def dump_regs(spi):
-    for reg_type, reg_data in regs_addr.items():
-        for reg_name, reg_addr in reg_data.items():
+def dump_regs(spi, cfgonly = False):
+    if cfgonly:
+        for reg_name, reg_addr in CONFIG_REGS.items():
             name :str = reg_name
             value = read_register(spi, reg_addr)
             print((name+":").ljust(15) +hex(value).ljust(4)+"\t"+str(value))
+    else:
+        for reg_type, reg_data in regs_addr.items():
+            for reg_name, reg_addr in reg_data.items():
+                name :str = reg_name
+                value = read_register(spi, reg_addr)
+                print((name+":").ljust(15) +hex(value).ljust(4)+"\t"+str(value))
 
 def sleep(t):
     return time.sleep(t)